elohim1 : Divorced tranny to Turbo 400 drive shaft question

Divorced tranny to Turbo 400 drive shaft question
Post by elohim1 on Jun 22, 2006, 7:23pm

I am committed to using a divorced 205 to a 2wd turbo400. The fellow I bought the tranny off of sent me a tranny that would bolt directly to a NP205. He said he will send me the housing to put on the end so the th400 will accept a yoke. I have the deuce drive shafts which has the 1410 yokes. One of the deuce shafts has real large yokes which I will use for the rear.

I was planning on cutting one of the deuce shafts down which has the 1410 yokes, to run in between the 205 and th400.

This will make it a 1410 at the T-case and tranny.

The fellow said he didnt know if he had any 1410 yokes, he did say he had 1530, however that will not work with my shafts.


Question

1) Is there a bolt on 1410 yoke made for the TH400?

2) should I use a slip joint in the jack shaft?

3) Should I use some other setup that I am not aware of at the th400?

Thanks
Chris

Re: Divorced tranny to Turbo 400 drive shaft quest
Post by tacomainoh on Jun 23, 2006, 12:21am

1. Not sure. Call Jess at High Angle. He's the man.

2. No. Nothing's moving forward and back.

3. Probably: unless you got the sh*tty long 32spl 4wd version of the TH400, the shaft will be way too short to use a 2wd tailhousing. I just went out and looked at my 2wd and 4wd trannies: the 4wd one has a VERY short 32spl output shaft for the 203, as does the one for the 205. The 2wd 400's I have have much longer shafts.
I would say you are going to need a new output shaft and a few phone calls. Not a big deal.

Re: Divorced tranny to Turbo 400 drive shaft quest
Post by davea on Jun 23, 2006, 1:42am

Yep, the transmission output shaft for a 2wd and a 4wd are different.

Re: Divorced tranny to Turbo 400 drive shaft quest
Post by wetcj on Jun 23, 2006, 7:12am

And just in case you didn't know, output shaft change requires complete transmission disassembly.

Re: Divorced tranny to Turbo 400 drive shaft quest
Post by tacomainoh on Jun 23, 2006, 10:34am

Yes, it does.

there are some subassemblies but it's still kind of a job. Got friends that work at tranny shops?

Re: Divorced tranny to Turbo 400 drive shaft quest
Post by 40grit on Jun 23, 2006, 1:52pm


Quote: <TABLE class=bordercolor cellSpacing=1 width="90%"><TBODY><TR><TD width="100%"><TABLE class=quote cellSpacing=0 cellPadding=2 width="100%"><TBODY><TR><TD width="100%">
2. No. Nothing's moving forward and back. </TD></TR></TBODY></TABLE></TD></TR></TBODY></TABLE>


that would depend on how both the tranny and the 205 are mounted..there could be a need for the driveshaft to extend/retract a little due to torque moving one of the 2 housings ( or both) along with making it super easy to install without having to remove tranny or 205 to put jackshaft in...

Re: Divorced tranny to Turbo 400 drive shaft quest
Post by tacomainoh on Jun 23, 2006, 2:04pm

OOPS

yeah, a little slip would sure make it easier to install. Good catch LOL

Torque won't move the housings back and forth though....

Re: Divorced tranny to Turbo 400 drive shaft quest
Post by luckypabst on Jun 23, 2006, 2:55pm

It can change the center to center distance between the yokes, more so with a flexy frame or real soft mounts.

Re: Divorced tranny to Turbo 400 drive shaft quest
Post by 40grit on Jun 23, 2006, 3:15pm

not back and forth, but torque up and away from "unloaded" position, which effectively makes the shaft longer ( not by very much, but more than a non-slip could handle)

p.s. Taco,
If your engine doesn't have enough torque to move rubber mounts, you need to scrap that puppy..LOL

Re: Divorced tranny to Turbo 400 drive shaft quest
Post by bbm715 on Jun 25, 2006, 10:24am

Uh, guys, if he's using a 2wd automatic transmission then the trand yoke is already a slip - just use a solid jackshaft but make sure the trans yoke is out a little (so if you flex you aren't trying to shove it thru the trans tailhousing.