Does anyone have a picture or a good drawing of the brackets that bolt to the muffler? The maintenance manual has the best drawing I've seen, but it leaves a lot to the imagination.
Thanks all!
Printable View
Does anyone have a picture or a good drawing of the brackets that bolt to the muffler? The maintenance manual has the best drawing I've seen, but it leaves a lot to the imagination.
Thanks all!
I can take a few exhaust photos later today.
I don't know if I have an extra bracket that I can make a tracing of, but I will check.
I couldn't make it to the garage today:confused: , but here are few photos that I had on a SD card to ponder over until tomorrow. I will get that thickness also.
Front view: I fastened the cable with bolts at the muffler. I still have to make the correct pins. Can't find them for sale. I will have to copy one of the originals that was still on the frame mount.
https://i.imgur.com/uy6cTMdl.jpg
Can't see "C" bracket in this rear view of muffler rear flange:confused: it's on the outer side of pipe toward the frame. But same setup.
Crap! I need to dust the inside of the frame rails.
https://i.imgur.com/4TXr5Bul.jpg
Yeah! That's kind of what I thought they should be. From that angle, they don't look thick enough to need a 1 3/4" bolt, but I got 'em, sooo... [emoji846]
I think I saw the pins at the local hardware store. 1/4" x 1/2" (maybe?). I have the 2 pins in the crossmember/hanger to compare to if I can't look up dimensions from the NSN. I'll let you know what I end up with.
Dust the frame?! I'd think there was something wrong if I didn't have dirt, mud or rust falling all over me every five minutes. [emoji16]
Maybe some day! [emoji1]
Thanks!
Pins are 5/16 x 3/4 overall.
Sent from my moto x4 using Tapatalk
View of rear muffler hanger
https://i.imgur.com/eyxH7HWl.jpg
http://i.imgur.com/GZxiC2Yl.jpg
The slotted holes are needed to rotate the bracket around to take the slack out of the hanger cable.
I found a few NOS parts in my stash to photograph.
PM me with your mailing address, and I will mail you a tracing of the "C" bracket.
Oh yea, It's 1/8" thick.
http://i.imgur.com/6oCMm55l.jpg
Ohhhhh, slots! I didn't notice that in the first pictures. Yeah, I'll send you my email in a minute. Thanks for all the help. You've saved the day again!
Can you post a tracing on the site?
Here is the muffler bracket from jeepdan. Sorry about the low quality graph paper, it's from the internet. :rolleyes:
Four lines to the inch.
Thanks for posting this.
Ugh. When I was removing one of the pins, the cable snapped. So now I need a source for cables if anyone has one. I'll be calling VPW tomorrow, maybe they still have some.
Thanks everyone!
Sent from my moto x4 using Tapatalk
Yeah, that's kinda where my brain was going, too. I wonder though, if the ends are heated to the point that the old cable would slip out, wouldn't a new cable be able to be pushed in? But would it hold? That's the $64,000 question.
Sent from my moto x4 using Tapatalk
I think that a person could cut off the cable with a cut off wheel, and then drill the cable out of the eye.
Push a new length of cable in and swage the cable tight.
My all time favorite Jeepdan quote:
'I need to dust the inside of my frame rails.'
I may print shirts. That is awesome.
My temporary solution. The bottom loop is extra large because I tried to use a thimble but it never seemed to get tight enough. So I took it out. But hey, it's only temporary, right? [emoji16]https://uploads.tapatalk-cdn.com/201...7dc459a6df.jpg
Sent from my moto x4 using Tapatalk