HYDRO STEERING QUESTIONS
Post by robertcowan on Aug 26, 2006, 11:10pm
ANYBODY DRILLED THE SAGINAW STEERING BOX FOR HYDRO ASSIST LINES ? ALSO ANYBODT KNOW A GOOD PLACE TO BUY CYLINDERS FOR THE HYDRO SETUP ?
BOB
HYDRO STEERING QUESTIONS
Post by robertcowan on Aug 26, 2006, 11:10pm
ANYBODY DRILLED THE SAGINAW STEERING BOX FOR HYDRO ASSIST LINES ? ALSO ANYBODT KNOW A GOOD PLACE TO BUY CYLINDERS FOR THE HYDRO SETUP ?
BOB
Re: HYDRO STEERING QUESTIONS
Post by luckypabst on Aug 26, 2006, 11:13pm
I drilled mine. I suggest a complete disassembly to be certain you have all the shavings out, otherwise it's a pretty simple project. The how-to is all over the web so I won't bore you with any details.
Chris
Re: HYDRO STEERING QUESTIONS
Post by robertcowan on Aug 26, 2006, 11:15pm
WHERE DO YOU GET O/H PARTS FOR THE SAG. BOX CHRIS
Re: HYDRO STEERING QUESTIONS
Post by luckypabst on Aug 26, 2006, 11:23pm
I got mine at the local "quality" independent auto parts store.
Do note that there are two piston diameters and you should know what size yours is before ordering the kit. I wanna say the kit was like 35 bucks and you need a few special tools to set the box up when you put it back together. Also the internal balls are different diameters and should be different colors too - alternate sizes when you reassemble.
Chris
Re: HYDRO STEERING QUESTIONS
Post by robertcowan on Aug 26, 2006, 11:34pm
what box has the big piston in it
Re: HYDRO STEERING QUESTIONS
Post by robertcowan on Aug 26, 2006, 11:35pm
also what kind of special tools
Re: HYDRO STEERING QUESTIONS
Post by robertcowan on Aug 26, 2006, 11:49pm
i read agr recomends the small piston pump it reacts quicker , huh ?
Re: HYDRO STEERING QUESTIONS
Post by bluesman2a on Aug 27, 2006, 1:06am
A couple of notes, Chris already covered a few:
1) You want the big piston box (steering gear, not the saginaw pump). AGR are clowns, PSC or West Texas Offroad are much better sources for info. Both of them use the big piston gears.
2) I think the J-Trucks (larger ones) had the more desirable gears.
3) Standard tools are 1/4 NPT tap, appropriate drill-bit, then you can put in an NPT to AN (also JIC-37) and run all your lines in straight hydro (spares are easier too).
4) If you want one that's already done, PSC sells a very nice box pre-tapped. That's the direction I went. If you're not sure of your re-assembly skills, West Texas Offroad will tap a box you send them.
5) Pump -- you want high-volume.
6) Cylinder -- If you're going to use it on the road, then do not get anything larger than 1.75" they are too slow for street use. If you want brute force, get a 2" agro ram. Northern Tool carries a good line of agro rams which are nice cause they are rebuildable. In in a streetable ram, I would check out either PSC's or Mad 4WD's. There is also a guy on the Pirate 4X4 board who goes by "Station" who is supposed to have some very nice stuff.
Re: HYDRO STEERING QUESTIONS
Post by tacomainoh on Aug 27, 2006, 1:42am
Rocklogic sells a nice kit for not much money, like $250. Very good little ram, very effective up to at least the 46's Tommer is running.
Re: HYDRO STEERING QUESTIONS
Post by bigwheelbob on Aug 27, 2006, 7:07am
Here ya go! http://www.pirate4x4.com/forum/showthread.php?t=502676
Site Upgrade, Design Modifications & Administrative Support by: Palm River Enterprises LLC, IT Solutions President: Tom King, User ID=teking |
This site is owned and operated by: M715 Zone, LLC President: Jon Schmidt, User ID=brute4c |
Copyright Notice: This web site is subject to the protection of the copyright laws of the United States and other countries. Except for Personal Use Only, you may not modify, copy, distribute, transmit, display, perform, reproduce, publish, license, create derivative works from, transfer, or sell any information obtained from any part of the M715 Zone website without the prior written permission of M715 Zone, LLC. Written permission can only be obtained by contacting brute4c@m715zone.com |
![]() |