Forums | Basic Training | Online Maintenance Manuals | The M715 Zone Vin Registry | VPW's M715 Parts List | Galleries | Links |
|
|
Thread Tools | Display Modes |
#11
|
||||
|
||||
![]()
Re: Radiator in the bed ??
Post by barrman on Nov 2, 2006, 9:59am Here is the best picture I have of the fan here at work. It was taken over a year ago, but you get the idea. ![]() |
#12
|
||||
|
||||
![]()
Re: Radiator in the bed ??
Post by barrman on Nov 2, 2006, 10:00am I still have enough room in front of the fan to use a short socket and a 3/8" ratchet drive to install the bolts. |
#13
|
|||
|
|||
![]()
Re: Radiator in the bed ??
Post by elohim1 on Nov 2, 2006, 6:52pm Quote:
Yes, please send pics of this tilt setup to : elohimfirst@msn.com Thanks Chris Good info. gents. |
#14
|
||||
|
||||
![]()
Re: Radiator in the bed ??
Post by 40grit on Nov 2, 2006, 8:27pm sorry boss, got so friggen busy with DieHard4 filming today...I'm going in tomorrow to work on 715, i'll get them tomorrow... |
#15
|
||||
|
||||
![]()
Re: Radiator in the bed ??
Post by 40grit on Nov 3, 2006, 4:53pm ok, here's a bunch... front view, ground level [img=http://img292.imageshack.us/img292/5607/coresupport002qc6.th.jpg] top view [img=http://img126.imageshack.us/img126/7586/coresupport003ty0.th.jpg] passenger side rear view [img=http://img293.imageshack.us/img293/4955/coresupport004ht4.th.jpg] driver side rear view [img=http://img527.imageshack.us/img527/4599/coresupport005aw2.th.jpg] yet another view [img=http://img170.imageshack.us/img170/7326/coresupport006el6.th.jpg] radiator I'm using, with Flexilite 292 monster fans ( 31x19 universal Gm rad) [img=http://img527.imageshack.us/img527/2104/coresupportsc1.th.jpg] no put together pics, but the rad fits in front, about 3" further forward than stock with the fans behind it...leaves about 1" to front of water pump serp pulley...still has room for auto tranny cooler in front if I decided to change down the road... supports are made of steel framing member, cost $11 for 10' section, cut a few pieces out, bent some in half lengthwise and used them for front supports, with a thin strip of rubber, it fits perfect around tanks on radiator, just need to fab top and bottom brackets, and drill holes for fans to mount... |
#16
|
|||
|
|||
![]()
Re: Radiator in the bed ??
Post by elohim1 on Nov 3, 2006, 9:29pm Much appreciated 40grit !!! |
Thread Tools | |
Display Modes | |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
elohim1 : On board air with GM compressor ?? | Elohim1 | PseudoZone - Mod Tech Archive | 13 | December 15th, 2009 05:24 PM |
elohim1 : BBC header selection, what did you use? | Elohim1 | PseudoZone - Mod Tech Archive | 30 | December 15th, 2009 04:48 PM |
elohim1 : Serpentine system and ON board Air ?? | Elohim1 | PseudoZone - Open Archive | 3 | November 11th, 2009 11:29 PM |
elohim1 : What is the spacing on the points for a 230? | Elohim1 | PseudoZone - Open Archive | 4 | November 11th, 2009 02:09 AM |
elohim1 : Which 502 motor should I use? | Elohim1 | PseudoZone - Open Archive | 11 | November 11th, 2009 01:46 AM |