militarypotts Spec/4 Military Police, Vietnam Era, "Does the noise in my head bother you? Welcome to the Twilight Zone!"
Sorry to take so long to respond. Been really busy,working here and we are 14 hours ahead so it's day here; night where you are.
The ignition is rather straightforward in an M715. Wire #12 comes from the ignition switch on the dash panel. When you turn it "on", you supply 24V to the wire on the side of the ignitor. You should be able to see 24Volts on that wire (reference to ground) when the switch is on. If not, you need to see where it is getting interrupted. For instance, is there a hidden "Kill" switch between the ignition switch and the ignitor? If the correct voltage is being supplied, then we have an internal issue in the ignitor. Unlike many American cars, there is no ballast resistor on the firewall and no ballast resistor bypass set of contacts on the starter button.
What that did was to give full 12 volts to a coil when starting. Then when the key was released, the 12 volts would have to go through a ballast resistor when in the "Run" position, supplying about 8Volts (talking a 12volt sustem of course). Our trucks originally had a ballast resistor but it was eliminated. We have no ballast bypass contacts.
Clear as mud yet?
It would be possibpe to take that large blank metal plug out of the ignitor and connect a wire to it to monitor the voltage as you drive.
Clear as mud to me, but I figured the first thing I needed to do was check for 24 volts going to the ignitor. Where would I get that reading under the cap?
militarypotts Spec/4 Military Police, Vietnam Era, "Does the noise in my head bother you? Welcome to the Twilight Zone!"
Just unscrew the wire/connector that screws into the side of the ignitor and check the center pin of the connector. That is the 24 Volt feed. In the online -20 manual, Chapter 2, Section 14, Figure 2-29 Ignitor, it is number 2 in the illustration.
You shouldn't have to take the cap off.
Thanks Don, I will try to get around to that this weekend. Ignition switch in the on position. Does someone need to hit the starter switch while I'm checking the reading?
militarypotts Spec/4 Military Police, Vietnam Era, "Does the noise in my head bother you? Welcome to the Twilight Zone!"
Just a thought here. Should, I get a 24 volt reading at the ignitor, what would be my next step? Also, when installing a Pertronic's in the ignitor, is their any special way the magnetic collar slips over the distributor shaft? I did it gently and made sure it was all the way down as far as it would go. I feel I installed everything correctly because my truck fired up immediately upon putting it all back together.
militarypotts Spec/4 Military Police, Vietnam Era, "Does the noise in my head bother you? Welcome to the Twilight Zone!"
Ignition switch "ON", no need to step on the starter because this circuit is very basic, unlike most automotive circuits.
As for the Pertronix system, unfortunately I don't have any experience with one so I will yield to another member who has experience with one. Not saying that they are a problem. Probably much more reliable in the long ru..
You know Don, I could always switch it back to points and a condenser, but I've heard such positive reviews on the Pertonix system. I think my problem lies within the coil I'm sorry to say. Not sure what the seller of it is going to say or do about it though. Literally got 3 starts out of a supposedly new coil.
militarypotts Spec/4 Military Police, Vietnam Era, "Does the noise in my head bother you? Welcome to the Twilight Zone!"
As I've said before my "new" china coil lasted about 2 miles. Once they cool down, they will usually work again till hot. That being said, no way to test them unless you heat it up. The US NOS coils are now very hard to find.
Going back to points will not change the operation of the coil. I'm sure the electronic system you installed heats the coil just the same. I always thought those electronic systems had their own special coils but I now assume not.
SFC, HQ,129th Sig Co, PAARNG, Vietnam Era
The Pertronix collar should index to a notch on the distributor shaft. Mine did, and every distributor (ignitor, etc.) I've ever seen has had some similar feature to index the rotor.
Site Upgrade, Design Modifications & Administrative Support by: Palm River Enterprises LLC, IT Solutions President: Tom King, User ID=teking |
This site is owned and operated by: M715 Zone, LLC President: Jon Schmidt, User ID=brute4c |
Copyright Notice: This web site is subject to the protection of the copyright laws of the United States and other countries. Except for Personal Use Only, you may not modify, copy, distribute, transmit, display, perform, reproduce, publish, license, create derivative works from, transfer, or sell any information obtained from any part of the M715 Zone website without the prior written permission of M715 Zone, LLC. Written permission can only be obtained by contacting brute4c@m715zone.com |