ForumsBasic TrainingOnline Maintenance ManualsThe M715 Zone Vin RegistryVPW's M715 Parts ListGalleriesLinks

Go Back   M715 Zone > General Tech > Stock Tech > Stock Tech Archives

Stock Tech Archives Look here first for all archived messages

 
 
Thread Tools Display Modes
  #1  
Old March 31st, 2004, 03:46 AM
Nuke_grant Nuke_grant is offline
Civilian
 
Join Date: Mar 2004
Posts: 2
Nuke_grant is an Observer
Default e brake help!

I've removed everything in my NP200 except the shift forks/rails and the dual gear assembly in the middle. A few taps on each end doesn't free it. How do I remove that middle gear set?

Is there a TM that has rebuild specs or an exploded parts view for this NP200?

Thanks for any help,
Grant
  #2  
Old March 31st, 2004, 06:43 AM
Kaiserjeeps's Avatar
Kaiserjeeps Kaiserjeeps is offline
Sergeant
 
Join Date: Dec 2003
Location: Idaho panhandle
Posts: 1,396
Kaiserjeeps is a Soldier
Default

Grant, Check the online manuals over there.....
<- <-<-<-------
__________________
Build quality and they will find you.

JEEP,

Just Engineer Everything Properly

Living in the round at 1200 feet
  #3  
Old March 31st, 2004, 08:59 AM
brute4c's Avatar
brute4c brute4c is offline
Grand Poobah
 
Join Date: Sep 1998
Location: North Central Wisconsin
Posts: 11,492
brute4c is a Soldier
Default

There are 2 manual sections to look at...the first is the detailed stuff on teardown and rebuild:
http://www.m715zone.com/manuals/34/chapter12.html
The 2nd is the removal, reinstall and external adjustments, like shift linkage, etc.
http://www.m715zone.com/manuals/Chap...ection_20.html
That should do ya...let us know if ya need more.
brute4c
__________________
Lord send your Holy Ghost into our hearts and make the desire of our hearts Your Will.

Pro-choice, that's a LIE, babies don't choose to die!!
  #4  
Old April 1st, 2004, 03:41 AM
Nuke_grant Nuke_grant is offline
Civilian
 
Join Date: Mar 2004
Posts: 2
Nuke_grant is an Observer
Default

Thanks guys. I just spent the past 4 hours kneeling over my 200.

"Drive shaft from case using a plastic hammer." Thats a good one. It took a drift and some hard whacks to get it past the first bearing. After that it went good. Is this normal? I don't know of ANY plastic hammer that would have done what was needed to remove my shaft.

Another thing, the manual says that you have to use the screw arbor tool to reassemble the idler gear assembley (to not damage the shim). I noticed that until you put the 196ft/lbs onto the shaft that the last bearing has a little wiggle. Would it be possible to put the case together without this arbor thing?

This is my first t-case/transmission rebuild. What an experience.

Grant
  #5  
Old April 1st, 2004, 05:15 PM
LuckyPabst's Avatar
LuckyPabst LuckyPabst is offline
Private 1st Class
 
Join Date: Dec 2003
Location: Lone Pine, CA
Posts: 451
LuckyPabst is a Soldier
Default

Grant, I used an aluminum drift and bigass ball pein hammer or single jack. It was hard and fought me most of the way out.

The arbor is to keep the little shim pack in alignment as you drive the idler shaft back in place. Without it you risk the shims moving around and at best not allowing the shaft to pass. At worst you'll munch or bend part of the shim which could cause other problems. I think I'll set the case on it's side and carefully insert the shaft, with the shims on the low side of the assembly. Once the shaft is past them it should be a breeze (a hammer induced breeze).

Chris
 

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Oil Pump Gear rboltz Stock Tech 13 February 13th, 2009 08:06 AM
NP 200 to NP 205 speedo gear. wrecker Modified Tech 8 August 8th, 2008 10:14 AM
T-98 stuck in first gear Jed Stock Tech 5 December 24th, 2007 03:43 PM
Gear Ratios ron Modified Tech 5 November 27th, 2007 11:47 AM


All times are GMT -7. The time now is 03:10 PM.

 

Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
1998 - 2019


This site is owned and operated by:
M715 Zone, LLC
President: Jon Schmidt, User ID=brute4c
If you have any suggestions, comments, problems or questions, contact:  brute4c@m715zone.com

Use of this site means you understand and agree to our TERMS OF USE

Copyright Notice:
This web site is subject to the protection of the copyright laws of the United States and other countries. Except for Personal Use Only, you may not modify, copy, distribute, transmit, display, perform, reproduce, publish, license, create derivative works from, transfer, or sell any information obtained from any part of the M715 Zone website without the prior written permission of M715 Zone, LLC.

Written permission can only be obtained by contacting
brute4c@m715zone.com

Copyright 1998-2019