ForumsBasic TrainingOnline Maintenance ManualsThe M715 Zone Vin RegistryVPW's M715 Parts ListGalleriesLinks

Go Back   M715 Zone > General Tech > Open Discussion

Open Discussion Open Discussion for all M715 series trucks

Reply
 
Thread Tools Display Modes
  #1  
Old August 10th, 2009, 08:49 PM
Fastfrankie Fastfrankie is offline
Private 1st Class
 
Join Date: Dec 2006
Location: New Jersey by Philadelphia
Posts: 305
Fastfrankie is a Soldier
Default Front brake shoes wet...

Pulled off my front driver drum today and the new shoes were somewhat wet and had asbestos mucked up a bit in the holes where the shoes are rivited.

I put in new wheel cylinders about a year ago (E350 Ford ones) and am assuming its the front seal for the axle, although I am not sure. I was able to use a can of Brakekleen and a toothbrush to clean the shoes off rather easily.

Any ideas? How hard is it to replace the front seal - any pictures? I do have the manual, just not in front of me now. I cannot imagine the wheel cylinder leaking since they can't have but 100 miles on them. I am assuming that the knuckle/axle seal may be original...and 40 years old.

Any way to tell what it is?
Reply With Quote
  #2  
Old August 10th, 2009, 10:00 PM
brute4c's Avatar
brute4c brute4c is offline
Grand Poobah
 
Join Date: Sep 1998
Location: North Central Wisconsin
Posts: 11,375
brute4c is a Soldier
Default

If it is gear oil, the seal is way down the tube by the center section where the gears are...a little outboard of the center but not much.

If its grease, it could be the hub seal for the bearing...the knuckle is sealed by the spindle from the drum area...if you see leakage around the spindle mount, then the knuckle...harder to leak that way I would think.

Did you put grease on the backing plates to prevent squealing/chirping the lat time they were assembled? Did you maybe use a lot and it got all over the shoes?

Wild off the wall guess there...
__________________
Lord send your Holy Ghost into our hearts and make the desire of our hearts Your Will.

Pro-choice, that's a LIE, babies don't choose to die!!
Reply With Quote
  #3  
Old August 11th, 2009, 04:41 AM
Fastfrankie Fastfrankie is offline
Private 1st Class
 
Join Date: Dec 2006
Location: New Jersey by Philadelphia
Posts: 305
Fastfrankie is a Soldier
Default

For some reason I am going to check the master cylinder level - it seemed like brake fluid. Upon thinking about it, if it were axle grease or axle oil, it would be dripping where at the bottom under the spindle, where there is a gasket at the knuckle.

For what its worth, when I put a clean pan under the brake assembly and hosed it down with Brakekleen, it all went into the pan. The color was of rust color which leads me to believe it has brake fluid in it.

I'm going to depress the pedal to see if there are any leaks.

Anyone else?
Reply With Quote
  #4  
Old August 11th, 2009, 06:39 AM
Barrman's Avatar
Barrman Barrman is offline
Chief 9-flats

 
Join Date: Dec 2003
Location: Giddings, Texas
Posts: 7,705
Barrman is a Soldier
Default

Don't push the pedal too far down with the drums off. You could pop the pistons out of the wheel cylinder. Feel around the dust covers of the cylinder. If it is brake fluid, they will be wet.

Did you replace the brake hoses and clean out the lines when you put on the new cylinders? Any dirt, crud, rust, etc... that was there before could have gotten into the new parts and made them leak. Don't discount them as bad just because they were "new" at one point.

My master did a similar fall to useless. I swapped over to DOT 5 Sunday so this new one might actually last more than 4 years.
__________________
Remember if you didn't build it you can't call it yours.

6.2 powered M715, 5 M1009's, M416, 2 M101's, 2 M105's, 3 M35's, M1007 6.5 turbo Suburban project called Cowdog.
Reply With Quote
  #5  
Old August 13th, 2009, 07:30 PM
randyscycle's Avatar
randyscycle randyscycle is offline
Staff Sergeant
 
Join Date: Jul 2007
Location: Rhoadesville, Virginia (five miles from no place)
Posts: 5,396
randyscycle is a Soldier
Default

Just pull the boots back on the wheel cylinders and see if there is any fluid in there. That should be dry or nearly dry in there. That will tell you if you have a leaky wheel cylinder.
__________________
"Free advice is worth what you pay for it."
Reply With Quote
  #6  
Old August 17th, 2009, 05:23 PM
wolf.dose's Avatar
wolf.dose wolf.dose is offline
Private 1st Class
 
Join Date: May 2008
Location: Germany
Posts: 411
wolf.dose is a Soldier
Default

That might be the wheel cylinders. New means not functioning. Did you know, when you assembled the wheel cylinders, how old are they? Have they been propperly assembled, is the surface inside ok?
I ALLWAYS disassemble new wheel cylinders, clean them in straight alkohol, check the inside, rework them, clean again, regrease with brake grease blue and reassemble them. I had the experiance before that a new whell cylinder is leaking after several weeks for I did not follow the known procedure.
If it is grease or oil you will fell it between your finger tips. Than you have to take the side of the axle appart and propperly reassembel it with the correct torque values. Else you overstress the bolts and they will fail. In part 34 you find a desription of this work.
M715 since 1982

Wolf
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Brake Shoes terryb Open Discussion 65 January 29th, 2018 02:17 PM
Brake shoes for dummies fng Stock Tech 18 July 27th, 2014 10:07 AM
oilcan : modified modern brake shoes for stock axles oilcan PseudoZone - Open Archive 4 November 10th, 2009 11:06 PM
wheel cyl and brake shoes need angler Modified Tech 3 May 21st, 2007 07:07 PM
Are there FRONT and REAR brake shoes? FSJGuy Stock Tech Archives 12 April 8th, 2004 12:15 PM


All times are GMT -7. The time now is 09:41 PM.

 

Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
1998 - 2019


This site is owned and operated by:
M715 Zone, LLC
President: Jon Schmidt, User ID=brute4c
If you have any suggestions, comments, problems or questions, contact:  brute4c@m715zone.com

Use of this site means you understand and agree to our TERMS OF USE

Copyright Notice:
This web site is subject to the protection of the copyright laws of the United States and other countries. Except for Personal Use Only, you may not modify, copy, distribute, transmit, display, perform, reproduce, publish, license, create derivative works from, transfer, or sell any information obtained from any part of the M715 Zone website without the prior written permission of M715 Zone, LLC.

Written permission can only be obtained by contacting
brute4c@m715zone.com

Copyright 1998-2019