ForumsBasic TrainingOnline Maintenance ManualsThe M715 Zone Vin RegistryVPW's M715 Parts ListGalleriesLinks

Go Back   M715 Zone > General Tech > Open Discussion

Open Discussion Open Discussion for all M715 series trucks

Thread Tools Display Modes
Prev Previous Post   Next Post Next
Old November 17th, 2017, 01:17 PM
RRatch RRatch is offline
New Recruit
Join Date: Jul 2017
Location: Southeast PA
Posts: 15
RRatch is a Soldier

Quick thanks for the Chevy WC part numbers.

I just did a complete replacement of the stock brake system on my blue '67. Corvette MC, lines, and new wheel cylinders, without any drilling.
My lines were in good shape, but they were full of crud and rust never sleeps, so I replaced all with Cupro-Nickel anyway. Every point fluid touches is brand new.

I used the Chevy WC's, but could only find 7 right side units (I have 2 trucks), so went with that on both sides and just compensated in line routing on the left side.

The pedal is nice and firm, and stops the wheels on jack stands pretty well. Road test this weekend...

Here's my "after-action" summary and material list:

$172 total

Multiple fittings for 3/16 And 1/4 line:

25' rolls of 3/16 And 1/4 cupro line with various fittings:

Double flaring kit:

Rear axle 3/16 fitting hose:
ACDelco 18J2119

Wheel cylinders (1/4 thread inputs)
$19.04 ($4.76 ea)
part no. WC9344/EW9345 (all passenger side, but works on either)

Master Cylinder (corvette, non-power brakes):
$31.93 ($25 on 11/17/17)
Cardone Select 13-1371 New Brake Master Cylinder

(2) Front axle 3/16 fitting female ended hoses (usable, but too short for factory location; requires some bracket fab and steel line extending)
$12.90 ($5.95 ea + ship)
Sunsong - 2203913 - $5.95 ea (new stock)
Raybestos - BH36599 - $4.46 ea (NOS) - not used in this project
Dorman - H36599 - $7.65 ea (NOS) - not used in this project

An important note is the hoses for the front wheels. The ones I used are about 6" too short compared to factory, so require rerouting the steel line and bringing it further from the wheel and lower on the chassis. I was running new metal lines anyway, so no big deal.
Nowhere to host pics, but I stupidly ran the wheel end metal line over the kingpin, so if I ever remove it, I'll have to remove the line and bleed the brakes. Didn't think of it until the job was done and something in my head said it wasn't right.

Also, these are probably not good stock replacement parts, but rather for an entire system rebuild. The wheel cylinders required 7/16-24 fittings, and I ran 3/16 to individual wheels. Every other fitting in the truck is standard to the line size, EXCEPT at the master cylinder, where I again needed 1/2-20 fittings to adapt down to 1/4" line (for the single line to the rear) and 9/16-18 to 3/16" to the front wheels.
Reply With Quote

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Master Cylinder Conversion - Upgrade Warthog Modified Tech 40 November 30th, 2019 08:15 PM
Wheel cylinder ? 93-12smoke Modified Tech 1 November 30th, 2009 10:31 PM
stock wheel cylinder Chef Stock Tech 2 September 30th, 2008 07:54 AM
Wheel cylinders to Vette master cylinder Q's Nuke_Bill Modified Tech Archives 10 March 31st, 2004 07:48 PM

All times are GMT -7. The time now is 07:49 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2020, vBulletin Solutions, Inc.
1998 - 2020

This site is owned and operated by:
M715 Zone, LLC
President: Jon Schmidt, User ID=brute4c
If you have any suggestions, comments, problems or questions, contact:

Use of this site means you understand and agree to our TERMS OF USE

Copyright Notice:
This web site is subject to the protection of the copyright laws of the United States and other countries. Except for Personal Use Only, you may not modify, copy, distribute, transmit, display, perform, reproduce, publish, license, create derivative works from, transfer, or sell any information obtained from any part of the M715 Zone website without the prior written permission of M715 Zone, LLC.

Written permission can only be obtained by contacting

Copyright 1998-2020