Results 1 to 10 of 13

Thread: Starting new project need help

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1

    Default Starting new project need help

    Ok so I just bought a 1967 m715 and now I need to get it running. It’s been sitting in a driveway for a couple years and it probably hasn’t run in at least 10. The brakes go to the floor with no resistance and I’m unsure if the engine is seized. Was thinking of starting by spraying lubricant in the cylinders and letting it set for a few days to get engine ready to start. Any tips here? Any thoughts on the brakes?

  2. #2
    Join Date
    Jan 2011
    Location
    Fernandina Beach, FL
    Posts
    3,689

    Default

    The brakes on these trucks are very straight forward, nothing fancy. They use a single master cylinder that actuates all four wheel cylinders at the same time. There are conversions to dual if you do a search. But I elected to keep everything "stock".

    Each of the wheel cylinders will need to be rebuilt no doubt or replaced. There are replacements out there and hopefully, your shoes did not get soaked with brake fluid and can be still used. The parts source for stock parts is somewhat dried up now. However, you can get NOS master cylinders from a few vendors and eBay. If the wheel cylinders are not pitted, the rubber is 1-1/16". You can get those from even the NAPA store.

    As for the engine, you can start by spraying Kroil or WD-40 and let it sit for a while. You can use the huge harmonic damper attach bolt with the appropriate socket and see if you can bump the engine after it has had the penetrating oil sitting in there for several days. If it has had the carburetor on it, that is a plus since it tends to slow the entry of moisture.

    Also, no doubt, the carburetor will need to be rebuilt. They are a very straight forward Holley model 1920. I have had good luck with the military rebuild kits. The rubber parts still seemed to be in good shape.

    Good luck and pictures are appreciated!

  3. #3
    Join Date
    Apr 2016
    Location
    Katy, TX
    Posts
    279

    Default

    Here is a good site for brake parts, etc. I bought my pads and other brake parts from here a few years back.

    https://www.boyceequipment.com/m37--m715-parts

  4. #4
    Join Date
    Jul 2009
    Location
    Louisville, KY
    Posts
    1,041

    Default

    Has anyone here used "Marvel Mystery Oil" to help loosen up an engine?
    Thanks for all the help!

  5. #5

    Default

    Welcome to the Zone and to M715s they are great trucks.

    Are you going to restore the M715 to original? just want to get it running and driving?

    Post some pictures of your M715 inside and out.

    Up top above the site banner there is a link to the military manuals(TMs) for our trucks download them. The TMs help a lot in trouble shooting and repairing problems.

    Search the Zone forums I'll bet 99% of you problems another zoner has had them and there is a thread with suggestion on fixes.
    "An axe. A real axe. An 'I'm out of ammo, let me grab the axe', type of axe!" steelsoldier FrankUSMC

  6. #6
    Join Date
    Sep 2014
    Location
    Wichita Falls, TX
    Posts
    603

    Default

    Quote Originally Posted by kyken View Post
    Has anyone here used "Marvel Mystery Oil" to help loosen up an engine?
    ^ Good stuff right there.

    I'd go ahead and plan on replacing the whole brake system. With luck your shoes and drums are still good, maybe the steel lines too, but most likely everything else will need replaced or rebuilt.
    And a dual reservoir master cylinder swap is a little easier if you replace the steel lines at the same time.

  7. #7

    Default

    The brakes go to the floor with no resistance
    Well the jeep ads do state that the truck is unstoppable...


Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


Site Upgrade, Design Modifications & Administrative Support by:
Palm River Enterprises LLC, IT Solutions
President: Tom King, User ID=teking
This site is owned and operated by:
M715 Zone, LLC
President: Jon Schmidt, User ID=brute4c


If you have any suggestions, comments, problems or questions, contact:  brute4c@m715zone.com
Use of this site means you understand and agree to our TERMS OF USE

Copyright Notice:
This web site is subject to the protection of the copyright laws of the United States and other countries. Except for Personal Use Only, you may not modify, copy, distribute, transmit, display, perform, reproduce, publish, license, create derivative works from, transfer, or sell any information obtained from any part of the M715 Zone website without the prior written permission of M715 Zone, LLC. Written permission can only be obtained by contacting brute4c@m715zone.com

Copyright 1998-2024