ForumsBasic TrainingOnline Maintenance ManualsThe M715 Zone Vin RegistryVPW's M715 Parts ListGalleriesLinks

Go Back   M715 Zone > General Tech > Modified Tech > PseudoZone - Mod Tech Archive

 
 
Thread Tools Display Modes
  #11  
Old December 15th, 2009, 05:06 PM
Barrman's Avatar
Barrman Barrman is offline
Chief 9-flats

 
Join Date: Dec 2003
Location: Giddings, Texas
Posts: 7,735
Barrman is a Soldier
Default barrman :

Re: Radiator in the bed ??
Post by barrman on Nov 2, 2006, 9:59am

Here is the best picture I have of the fan here at work. It was taken over a year ago, but you get the idea.

  #12  
Old December 15th, 2009, 05:06 PM
Barrman's Avatar
Barrman Barrman is offline
Chief 9-flats

 
Join Date: Dec 2003
Location: Giddings, Texas
Posts: 7,735
Barrman is a Soldier
Default barrman :

Re: Radiator in the bed ??
Post by barrman on Nov 2, 2006, 10:00am

I still have enough room in front of the fan to use a short socket and a 3/8" ratchet drive to install the bolts.
  #13  
Old December 15th, 2009, 05:06 PM
Elohim1 Elohim1 is offline
Private
 
Join Date: Dec 2006
Location: Oxford, Ohio 45056
Posts: 187
Elohim1 is a Soldier
Default elohim1 :

Re: Radiator in the bed ??
Post by elohim1 on Nov 2, 2006, 6:52pm


Quote:
I've got a 454 and a tilt front- I fit a stock Ron Davis dual pass rad. with two puller fans- fabbed a custom mount. Pass. fan motor misses alt. by about 1/4 inch. Works great though. Gimme your e-mail and I'll sent pix if it helps. Won't be till next week though, I'm headed to Mex this weekend


Yes, please send pics of this tilt setup to : elohimfirst@msn.com

Thanks
Chris

Good info. gents.
  #14  
Old December 15th, 2009, 05:06 PM
40Grit's Avatar
40Grit 40Grit is offline
Private 1st Class
 
Join Date: May 2004
Location: Anchorage, Alaska
Posts: 257
40Grit is a Soldier
Default 40grit :

Re: Radiator in the bed ??
Post by 40grit on Nov 2, 2006, 8:27pm

sorry boss, got so friggen busy with DieHard4 filming today...I'm going in tomorrow to work on 715, i'll get them tomorrow...
  #15  
Old December 15th, 2009, 05:06 PM
40Grit's Avatar
40Grit 40Grit is offline
Private 1st Class
 
Join Date: May 2004
Location: Anchorage, Alaska
Posts: 257
40Grit is a Soldier
Default 40grit :

Re: Radiator in the bed ??
Post by 40grit on Nov 3, 2006, 4:53pm

ok, here's a bunch...

front view, ground level
[img=http://img292.imageshack.us/img292/5607/coresupport002qc6.th.jpg]

top view
[img=http://img126.imageshack.us/img126/7586/coresupport003ty0.th.jpg]

passenger side rear view
[img=http://img293.imageshack.us/img293/4955/coresupport004ht4.th.jpg]

driver side rear view
[img=http://img527.imageshack.us/img527/4599/coresupport005aw2.th.jpg]

yet another view
[img=http://img170.imageshack.us/img170/7326/coresupport006el6.th.jpg]

radiator I'm using, with Flexilite 292 monster fans ( 31x19 universal Gm rad)
[img=http://img527.imageshack.us/img527/2104/coresupportsc1.th.jpg]

no put together pics, but the rad fits in front, about 3" further forward than stock with the fans behind it...leaves about 1" to front of water pump serp pulley...still has room for auto tranny cooler in front if I decided to change down the road...

supports are made of steel framing member, cost $11 for 10' section, cut a few pieces out, bent some in half lengthwise and used them for front supports, with a thin strip of rubber, it fits perfect around tanks on radiator, just need to fab top and bottom brackets, and drill holes for fans to mount...
  #16  
Old December 15th, 2009, 05:06 PM
Elohim1 Elohim1 is offline
Private
 
Join Date: Dec 2006
Location: Oxford, Ohio 45056
Posts: 187
Elohim1 is a Soldier
Default elohim1 :

Re: Radiator in the bed ??
Post by elohim1 on Nov 3, 2006, 9:29pm

Much appreciated 40grit !!!
 

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
elohim1 : On board air with GM compressor ?? Elohim1 PseudoZone - Mod Tech Archive 13 December 15th, 2009 05:24 PM
elohim1 : BBC header selection, what did you use? Elohim1 PseudoZone - Mod Tech Archive 30 December 15th, 2009 04:48 PM
elohim1 : Serpentine system and ON board Air ?? Elohim1 PseudoZone - Open Archive 3 November 11th, 2009 11:29 PM
elohim1 : What is the spacing on the points for a 230? Elohim1 PseudoZone - Open Archive 4 November 11th, 2009 02:09 AM
elohim1 : Which 502 motor should I use? Elohim1 PseudoZone - Open Archive 11 November 11th, 2009 01:46 AM


All times are GMT -7. The time now is 01:43 AM.

 

Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
1998 - 2019


This site is owned and operated by:
M715 Zone, LLC
President: Jon Schmidt, User ID=brute4c
If you have any suggestions, comments, problems or questions, contact:  brute4c@m715zone.com

Use of this site means you understand and agree to our TERMS OF USE

Copyright Notice:
This web site is subject to the protection of the copyright laws of the United States and other countries. Except for Personal Use Only, you may not modify, copy, distribute, transmit, display, perform, reproduce, publish, license, create derivative works from, transfer, or sell any information obtained from any part of the M715 Zone website without the prior written permission of M715 Zone, LLC.

Written permission can only be obtained by contacting
brute4c@m715zone.com

Copyright 1998-2019